Replacing Lock on uPVC Door
To replace the lock, you need to first take off the screw holes and handle. This is typically easy to accomplish.
The next step is to find the screw that holds the lock barrel in place. This is typically a different color than the other screws, and is situated at the top of the faceplate of the lock.
Remove the Cylinder
The first step in changing a lock on a door made of upvc is to remove the old lock cylinder from the door. This is a easy process that can be done in around 30 minutes. All you require is a screwdriver. The Euro Cylinder screw is normally located on the inside edge of the door, right next to the lock cylinder. The screw must be easily identified because it is typically different from the rest of them. Remove the screw and store it in a safe place.
After removing the cylinder you can then begin removing the handle. To do this, open the door to allow full access to the edging on the inside of the door and the side of the lock faceplate.
Start with a screwdriver and remove the screw fastening the handle to the door. Once this is removed, you should be able to pull the handle toward you and the rest of the mechanism will fall out of the door.
If you have trouble getting the handle off, you may need to remove the screw that holds it to the stud in the door frame. This can be done with the aid of a screwdriver or drill, and you will need to be careful not to strip the screw head or cross-thread it.
When you are ready to replace your cylinder, make sure that it is the correct size for the door you have. Cylinders are measured according to two points: (a), the distance from the center of the Fixing Screw to the bottom of the cylinder, and (b) the distance between the keyhole's hole the keyhole and the edge of the lockplate.
Take the handle off
The good news is that when your upvc handle gets stiff, floppy or loose, it's an easy problem to fix. The multipoint lock cylinder or other internal parts within the door, in between the handle and handle frame, are typically the reason. It is not uncommon for upvc locks to become worn due to the weather, heavy usage or simply ageing and this can cause problems with the locking mechanism or closing mechanism of the door.
The cylinder may wear out and make it difficult to turn the key. The lock can also become stiff, causing the handle to loosen. The cylinder is easily replaced, and this is a simple process. It can be done yourself, but you'll require some knowledge about how the mechanism functions. You'll have to remove the handle to be able to replace the cylinder.
You will need an electric screwdriver and measuring tape to do this. It is essential to know the exact size of your existing cylinder to be able to order a replacement cylinder that will fit. The cylinder is the element that lets you lock your door made of upvc, and it is essential to ensure that you get an identical replacement size.
To remove the old cylinder, you will have to remove the screws that secure it. Be careful not to remove the screws, as this could make it difficult to remove them in the future. Once the screws have been removed, the cylinder should come out easily.
Remove the Lock Barrel
Upvc is a very durable material that is designed to ensure that you and your family are safe. They come in a wide range of styles and colors that can suit any decor. These doors are also efficient in thermal energy and maintenance-free. They do not come without a few drawbacks. Over time the locking point or barrel lock can become faulty and need to replaced. It's a simple procedure however there are some things you should know prior to beginning.
You'll need to take off the door handle in order to get access to the screw that holds the lock cylinder in place. It's typically a different color from the rest of the screws and is situated on the edge of the door, just the keyhole. Take the screw off and store it in a safe location. Next, carefully slide out the outside and inside door handles. Make sure you do this slowly and not too fast as it can damage your uPVC door.
Once you have removed the handles, use a screwdriver to detach the screws that hold them to the door frame. This will enable you to better access the pins that keep the cylinder in position. After that, you can play around with the cylinder to see if it becomes loose. If it does, push it towards you and then out of the socket.
Once you have removed the old lock cylinder it is important to replace it with a new one that has anti-snap and anti-bump security. You can do this yourself if you have the right tools, or you can hire an expert locksmith to do it for you. This is a relatively easy task that will take about five minutes to complete.
Install the New Cylinder
A upvc lock could be damaged or broken in a variety of different ways. For instance, the cylinder may have become damaged or isn't working as it should. It is important to choose the right size replacement for your door's upvc lock. This is because if an wrong lock is used, it could result in your upvc door being more susceptible to a method known as 'lock snapping' which is the cause of 25 per cent of burglaries.
To prevent this from happening, it is essential that the correct cylinder is installed and the procedure to do so is relatively easy and only takes about five minutes. You will need an instrument to remove the screws that attach to the faceplate on the handle and the cylinder. Once you have done this, it is a simple task to switch them.
Make sure that you open the handle to gain access to the lock cylinder on the side of the faceplate of the handle. This will let you easily remove the lock cylinder from the handle without the need to move it and expose the internal components of the frame.
The next step is to remove the old cylinder and measure it. You will need to determine the length of the cylinder and the diameter of the cam, which moves to lock and unlock the door. This will enable you to locate a replacement cylinder that's the same or smaller. This is the most crucial part of the entire process. A cylinder should fit flush with the backplate of the handle and have no more than 5mm protruding from it.
Install the Handle
It is not unusual for a upvc door lock to stop working and this could be caused by something breaking inside the case that controls the bolts that retract into the strike or keep plate. Often this can be resolved by making an Allan key adjustment beneath the hinges of the door but occasionally this could put excessive pressure on components inside the central case, so it is best to call a professional out.
During the changing process it is important to have easy and quick access to both sides of the handle as well as having the appropriate tools. It is a good idea to prop the door up to ensure that it doesn't close during this process.
The first step is to loosen the screws that hold the handle together using the help of a screwdriver. Once the screws have been loosen then you can remove the handle. After taking off how to replace window locks and the handle, it's now time to put in the new handle. Make sure the new handle is of the correct size for the cylinder you have currently and hole center. To determine the proper size take a measurement of the spindle's length on the lever you currently have. Make sure that the screw fix centre on the handle is the same as the screw fix centre on your current hole centre or cylinder.
The replacement handles made by Fab and Fixed are available in a variety of styles and are built to last. These handles are ideal for those looking to upgrade their Upvc handle and increase security for their home. Having the right handle will ensure that your house is secure and safe, and will not be easy for thieves to break into.